SOLSolution
50 Hz · 380–415 V (3-phase) · CIF Jebel Ali (or FOB Nhava Sheva)
Rotary Vane Vacuum Pump for Vacuum Conveying in Middle East
Rotary Vane Vacuum Pump sized for dilute-phase pneumatic vacuum conveying — 200–1,050 m³/hr at 150–500 mbar vacuum — and built for the Middle East grid, climate and shipping route.
Yash exports the rotary vane / liquid-ring vacuum pump into Middle East for vacuum conveying the same way it builds for India — cast, machined and dynamically balanced in-house under an ISO 9001:2015 system — with the 50 Hz and Incoterm details handled for the destination. On this application the machine handles dilute-phase pneumatic vacuum conveying; Line length and vertical lift set the vacuum; conveying rate sets the airflow. Deeper vacuum keeps material entrained to the receiver.
Shipped to Middle East, the unit is built for 50 Hz / 380–415 V (3-phase) and moves CIF Jebel Ali (or FOB Nhava Sheva). Motors are de-rated for 45–50 °C ambient and coastal corrosion protection is specified where the site sits near the sea. The recommended models are YELV-650, YELV-1000, YELV-1200; each is dynamically balanced for the continuous duty vacuum conveying runs, and each ships with test certificates on request.
MDLRecommended models
Rotary Vane Vacuum Pump — the fit for vacuum conveying
Liquid-ring vacuum for wet, vapour-laden or heavy dilute-phase transfer where a dry machine would ingest moisture.
Line length and vertical lift set the vacuum; conveying rate sets the airflow. Deeper vacuum keeps material entrained to the receiver. Indicative only — final selection depends on your exact duty point, altitude and air temperature.
EXPBuilding for Middle East
- Frequency
- 50 Hz
- Three-phase voltage
- 380–415 V (3-phase)
- Single-phase
- 220–240 V
- Incoterms
- CIF Jebel Ali (or FOB Nhava Sheva)
- Ports
- Jebel Ali · Dammam · Jeddah · Hamad · Sohar
- HS code
- 8414 — air/gas blowers, fans & compressors
Motors are de-rated for 45–50 °C ambient and coastal corrosion protection is specified where the site sits near the sea.
Sewage & STP aeration
Continuous diffused-air aeration for sewage treatment plants across new urban districts — the single biggest blower pull in the region.
Desalination & water treatment support
Aeration, degassing and pneumatic duty supporting desalination and municipal water treatment plants along the coast.
Aquaculture
Diffused-air aeration for a growing Gulf aquaculture sector holding dissolved oxygen in intensive ponds and tanks.
Construction & cement
Pneumatic conveying and dust-handling for construction and cement plants — inlet filtration specified against fine abrasive dust; also serves oilfield-adjacent utility duty.
FAQRotary Vane Vacuum Pump for Vacuum Conveying — FAQs
Is the Rotary Vane Vacuum Pump rated for continuous vacuum conveying duty?
Yes — the recommended YELV-650, YELV-1000, YELV-1200 are dynamically balanced and built for the 24/7 load that vacuum conveying runs. The duty here is dilute-phase pneumatic vacuum conveying at 200–1,050 m³/hr / 150–500 mbar vacuum; the machine is selected to hold that point continuously, not just touch it on a test bench.
How is a Rotary Vane Vacuum Pump sized for vacuum conveying?
Sizing turns on two numbers — flow and vacuum. Line length and vertical lift set the vacuum; conveying rate sets the airflow. Deeper vacuum keeps material entrained to the receiver. On this duty most selections sit around 200–1,050 m³/hr at 150–500 mbar vacuum. Fix the duty point, add a design margin, and pick the smallest model that covers both; YELV-650 and YELV-1000 are the usual starting points.
RFQ / Request for Quotation
Rotary Vane Vacuum Pump for Vacuum Conveying in Middle East?
Send your duty point (200–1,050 m³/hr at 150–500 mbar vacuum), site voltage and destination port — an engineer sizes the model and quotes CIF Jebel Ali (or FOB Nhava Sheva).