SOLSolution
50 Hz · 380–415 V (3-phase) · CIF Jebel Ali (or FOB Nhava Sheva)
Centrifugal Blower for Plastics & PET Extrusion in Middle East
Centrifugal Blower sized for hopper loading, PET drying air and vacuum sizing — 300–2,000 m³/hr at vacuum and pressure — and built for the Middle East grid, climate and shipping route.
The right centrifugal blower for a plastics and PET extrusion duty in Middle East is the one whose airflow and flow match the process; everything else — voltage, crating, documentation — follows from the destination. Plastics & PET Extrusion means hopper loading, PET drying air and vacuum sizing — plan for 300–2,000 m³/hr and vacuum and pressure, and pick the smallest model that covers both.
Shipped to Middle East, the unit is built for 50 Hz / 380–415 V (3-phase) and moves CIF Jebel Ali (or FOB Nhava Sheva). Motors are de-rated for 45–50 °C ambient and coastal corrosion protection is specified where the site sits near the sea. The shortlist below (YBCB-CX-100A, YBCB-CX-125A, YBCB-CX-150A) is a starting point — real load figures turn it into a firm selection and a quote in 24 hours.
MDLRecommended models
Centrifugal Blower — the fit for plastics and PET extrusion
Compact cooling and drying-air supply on profile, sheet and pipe lines — steady volume at modest back-pressure.
| Model | Power | Flow (m³/hr) | Flow (CFM) | Vacuum (Pa) | Pressure (Pa) | Noise (dB) | Weight (kg) |
|---|---|---|---|---|---|---|---|
| YBCB-CX-100A | 2.0 HP | 1200-1450 | 706-853 | 2000 | 3000 | 74/90 | 28 |
| YBCB-CX-125A | 3.0 HP | 1950-2350 | 1130-1383 | 2400 | 3700 | 76/95 | 38 |
| YBCB-CX-150A | 5.0 HP | 2800-3300 | 1648-1942 | 3200 | 4400 | 80/100 | 54 |
Central conveying headers and vacuum sizing tanks need held head; cooling and air-ring duty needs volume at modest back-pressure. Indicative only — final selection depends on your exact duty point, altitude and air temperature.
EXPBuilding for Middle East
- Frequency
- 50 Hz
- Three-phase voltage
- 380–415 V (3-phase)
- Single-phase
- 220–240 V
- Incoterms
- CIF Jebel Ali (or FOB Nhava Sheva)
- Ports
- Jebel Ali · Dammam · Jeddah · Hamad · Sohar
- HS code
- 8414 — air/gas blowers, fans & compressors
Motors are de-rated for 45–50 °C ambient and coastal corrosion protection is specified where the site sits near the sea.
Sewage & STP aeration
Continuous diffused-air aeration for sewage treatment plants across new urban districts — the single biggest blower pull in the region.
Desalination & water treatment support
Aeration, degassing and pneumatic duty supporting desalination and municipal water treatment plants along the coast.
Aquaculture
Diffused-air aeration for a growing Gulf aquaculture sector holding dissolved oxygen in intensive ponds and tanks.
Construction & cement
Pneumatic conveying and dust-handling for construction and cement plants — inlet filtration specified against fine abrasive dust; also serves oilfield-adjacent utility duty.
FAQCentrifugal Blower for Plastics & PET Extrusion — FAQs
Which Centrifugal Blower model do I need for plastics and PET extrusion in Middle East?
For a typical plastics and PET extrusion duty of 300–2,000 m³/hr at vacuum and pressure, start with YBCB-CX-100A and step through YBCB-CX-100A, YBCB-CX-125A, YBCB-CX-150A as the load rises. Central conveying headers and vacuum sizing tanks need held head; cooling and air-ring duty needs volume at modest back-pressure. Send us your exact flow and airflow and an engineer confirms the model and quotes it CIF Jebel Ali (or FOB Nhava Sheva).
How do you ship a Centrifugal Blower to Middle East?
Orders move CIF Jebel Ali (or FOB Nhava Sheva), routed through Jebel Ali. Units are palletised and packed in seaworthy, ISPM-15 heat-treated wooden crates and declared under HS heading 8414. Commercial documents, certificate of origin and per-unit test certificates travel with the shipment on request; spares can follow by air freight.
RFQ / Request for Quotation
Centrifugal Blower for Plastics & PET Extrusion in Middle East?
Send your duty point (300–2,000 m³/hr at vacuum and pressure), site voltage and destination port — an engineer sizes the model and quotes CIF Jebel Ali (or FOB Nhava Sheva).